MSDS (Material Safety Data Sheet)

MATERIAL SAFETY DATA SHEET
(FOR COATINGS, RESIN AND RELATED MATERIALS)

MANUFACTURER'S NAME:
NIPPON PAINT VINH PHUC CO., LTD
Address: Lot 39 A- Quang Minh industrial zone. Vinh Phuc province
EMERGENCY TELEPHONE NUMBER:
(84 - 0211) 882241 (Quality Assurance Section)
INFORMATION TELEPHONE NUMBER:
(84 - 0211) 882241 – 882248 (Quality Control Dept.)

SECTION I - PRODUCT IDENTIFICATION
CHEMICAL NAME : N/A
TRADE NAME : H – 2500 HARDENER
CHEMICAL FAMILY : HARDENER

SECTION II - INGREDIENTS
INGREDIENTS
CAS No
Wt. %
OCCUPATIONAL EXPOSURE LIMITS
VAPOR PRESSURE
TLV (TWA)
PEL (TWA)
BLOCKED POLYISO CYANATE
Proprietary
60-65
Not est.
Not est.
N/A
BUTYL ACETATE
123-86-4
25-30
150ppm
150ppm
7.8 mmHg
ETHYL 3-ETHOXY PROPIONATE
763-69-9
15-20
Not est.
Not est.
0.09 kPa

Note: (RD) = repairable dust. © = ceiling limit. (Skin) = Skin penetrative. (mppcf) = Millions of particles per cubic foot., +, @ = Carcinogenic according to criteria established by ( = NTP += IARC @=OSHA)

SECTION III – PHYSICAL DATA
SPECIFIC GRAVITY : 1.06 kg/ dm3
VAPOR DENSITY : Heavier than air
EVAPORATION RATE: (n- BuAc = 1) : Slower than ether
PERCENT NON-VOLATILES : 64 %
APPEARANCE : Colorless liquid, Solvent odor.

SECTION IV – FIRE EXPLOSION HAZARD DATA
FLAMMABILITY CLASSIFICATION:
FLASH POINT : 24 oC
(Tag closed cup rapid tester)
UN : 3.3 (UN=1263)
EXTINGUISH MEDIA:
[X]FOAM [ ]ALCOHOL [X]CO2 [X]DRY CHEMICAL [ ]WATER FOG FOAM [ ]OTHERS

UNUSUAL FIRE AND EXPLOSION HAZARDS:
Closed containers may explode when exposed to extreme heat
SPECIAL FIRE FIGHTING PROCEDURE:
Wear self-contained breathing apparatus.

SECTION V – HEALTH HAZARD DATA
SIGNS AND SYMPTOMS OF EXPOSURE:
Eye watering, headaches, nausea, dizziness and loss of coordination.
EFFECTS OF OVEREXPOSURE:
INGESTION : Harmful if swallowed.
INHALATION : Irriates nose and throat. May irritate lung
SKIN EXPOSURE : May cause moderate skin irritation
EYE EXPOSURE : Cause irritation, reddening and blurred vision.

MEDICAL CONDITIONS PRONE TO AGGRAVATION BY EXPOSURE:
No applicable information was found.

PRIMARY ROUTE(S) OF ENTRY: [X] DERMAL [X] INHALATION [X] INGESTION

EMEGENCY AND FIST AID PROCEDURES:
INGESTION : Don’t induce vomiting. Refer to a doctor immediately.
INHALATION : Remove to fresh air.
SKIN EXPOSURE : Remove promptly by wiping followed by washing with soap and water.
EYE EXPOSURE : Flush eyes thoroughly with plenty of water at least 15 minutes

SECTION VI – REACTIVITY DATA
STABILITY: [X] STABLE [ ] UNSTABLE
HAZARDOUS POLIMERIZATION: [X] WILL NOT OCCUR [ ] MAY OCCUR

HAZARDOUS DECOMPOSITION PRODUCTS:
May produce hazardous products including carbon monoxide and low molecular weight organic monomers when exposed to extreme heat.
CONDITION TO ADVOID:
Do not expose to heat or ignition sources.
INCOMPATIBILITY (MATERIALS TO AVOID):
Avoid contact with strong alkalis, strong mineralacids and strong oxidizing agents.

SECTION VII – SPILL OR LEAK PROCEDURES
STEP TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
Provide maximum ventilation. Only personal equipped with proper respiratory and skin and eye protection should be permitted in the area. Remove all sources of ignition. Take up spilled material with sawdust, vermiculite, or other absorbent material and place into container for disposal.

WASTE DISPOSAL METHOD:
Waste material must be disposed of in accordance with national and local environmental control regulations.
Empty containers should be recycled or disposed of through an approved waste management facility.

SECTION VIII – SAFE HANDLING AND USE INFORMATION
RESPIRATORY PROTECTION:
Overexposure to vapors may be prevented by ensuring ventilation controls, vapor exhaust or fresh air entry. If exposure may or dose exceed occupational exposure limits, use NIOSH-approved respirator to prevent over-exposure.
VENTILATION REQUIREMENT:
Keep the concentrations of ingredients listed in section II below TLV
SKIN PROTECTION:
Wear protective clothing including apron and gloves constructed of nitrile rubber or neoprene rubber.
EYE PROTECTION:
Wear chemical type splash goggles or full face shield.
HYGIENIC PRACTICES:
Clean or discard contaminated clothing and shoes.

SECTION IX – SPECIAL PRECAUTIONS
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING:
Store in a cool dry, well-ventilated area away from heat and ignition sources. Keep container tightly closed.

OTHER PRECAUTIONS:
To avoid static charge build up, grounding and minimizing free fall distance is recommended.
For industrial use only.

ABBREVIATIONS:

Not est. = not established
N/A = not applicable
U/I = unknown information
(RD) = respiratory dust